Doulton Ultracarb® W9123006 W9123053 Original Water Filter Cartridge
ULTRACARB® W9123006 W9123053
The ceramic shell is fitted with an activated carbon block insert containing lead removal media.
Benefits: Removal of particles, pathogenic bacteria, cysts, etc. with additional chlorine, organics and lead removal capabilities.
Size: 10″ (254mm) long x 2″ (53mm) diameter. 3/4″ (16mm) short mount.
Supercarb Upgrade – Doulton Ultracarb & Ultrcarb SI upgrade for Supercarb & Supercarb SI.
Preparing the Filter for use
These instructions cover a variety of filter candle grades, therefore, please ensure that you follow the relevant instructions for the grade of candle that you have purchased Extreme cleanliness is important. Wash hands before handling the product and take care to ensure that no contamination of the components occurs during assembly.
Installation
When installing a new filter candle it is important to condition the filter with the incoming water using the following procedure:
Ultracarb
Rated Service Flow for Optimum Performance: 0.5 USGPM/1.9 LPM
Filter Capacity: 600 USG/2250 L
Pressure Filters
• Place the rubber O ring(s) over the threaded mount
• Screw the candle into the housing, ensuring that a seal is made with the O ring(s). Do not over tighten
• Open the isolation valve/tap to allow water to flow through the filter to waste for 10 minutes
• Allow the filter to stand unused overnight
• Open the tap again for 10 minutes and allow water to run to waste. The filter is now ready for use
• For optimum performance, water flow should be restricted to approximately 1½ litres per minute
Operation
Due to filtration of particulate contaminants from the water during use, the flow of water from the filter may reduce over a period of time. To restore the water flow to its normal level, remove the filter and scrub the surface evenly with a clean abrasive kitchen pad under running water or in a bowl, ensuring that the open ended plastic mount is clear of the water, to avoid contamination
Product Attributes
Weight: 0.8 kg
Part Number: W9123006
Range: BSP Short (¾ " / 16mm) Threaded Mount
Length: 10 inches (254mm)
Diameter: 2 inches (53mm)
Filter Performance: Micro filtration of Bacteria, Cysts, Particles. Chlorine, Organics and Lead.
FRANKE: NOT compatible with FRANKE Housings.
System: Pressure
BEST PRICE GUARANTEE
We aim to provide you with the best price available in Australia! If for any reason you find a better genuine online price, let us know where and we will match it.
Just email: info@waterfilterforfridge.com.au (please allow for freight component)
IF YOU ARE NOT 100% SATISFIED WITH YOUR PURCHASE WE OFFER A FULL REFUND OR REPLACEMENT.
waterfilterforfridge.com.au
We are the cheapest fridge part dealer in Australia
Compatible Models
Please refer to the product description above for compatible filter numbers, refrigerator models, and system model information.
If you cannot find your model number or are unsure whether this product is suitable for your system, please contact us before purchasing.
Contact Us for Compatibility SupportInstallation Guide
Please use the general guide below to help identify your filter type and follow the correct replacement process. Filter location and replacement steps may vary depending on your refrigerator or water filtration system model. Always refer to your appliance manual for the exact filter location and specific instructions.
Need Help Finding the Correct Filter?
Before ordering, compare your old filter, check the model number or filter code, and confirm the connector type. If you are unsure, please contact Water Filter Distributors for assistance.
Whole House System Installation Manual
For whole house filtration systems, please refer to the detailed installation manual below. Professional installation by a licensed plumber is recommended.
View Whole House Installation ManualTwin Cartridge Under Sink Installation Guide
For twin cartridge under sink systems, please refer to the installation guide below. This guide is suitable for systems supplied with a dedicated faucet, diverter valve, tubing and installation kit.
Important Notes
- Filter location and replacement steps may vary depending on your appliance or system model.
- Flush approximately 5–10 litres or 3–5 minutes of water after installation.
- Use with cold potable water only.
- Check for leaks after installation and reinstall if necessary.
- Always follow your appliance manufacturer's instructions.
Certification & Quality Assurance
Water Filter Distributors is operated by Mexi Trading Pty Ltd, an Australian owned and operated company. Our products are supplied with a strong focus on quality, safety and trusted filtration performance.
Important Certification Notice
- Certification details may vary depending on the specific product model.
- Please refer to the product description, packaging or official documentation for model-specific certification information.
- If you require confirmation for a specific product, please contact Water Filter Distributors before purchasing.